ADI公司的ADXL362是微功耗三轴MEMS加速度计,数字输出,加速度范围为±2/±4/±8 g, 工作电压1.8V-3.3V,电源电压2V和100Hz输出数据速率时的功耗为2μA,运动触发叫醒模式的功耗为300nA,器件提供12位输出分辨率,8位格式的数据,在±2 g范围的分辨率为1 mg/LSB,主要用在助听器,家庭保健设备,运动使能电源开关,无线传感器和运动使能计量设备.本文介绍了ADXL362主要特性, ADXL362功能方框图以及评估板EVAL-ADXL362Z主要特性和电路图.

ADXL362: Micropower 3-Axis MEMS Accelerometer: Digital Output, ±2/±4/±8 g Range

The ADXL362 is an ultra-low power 3-axis MEMS accelerometer that consumes less than 2 μA at a 100 Hz output data rate, and 300 nA in motion-triggered Wake-Up Mode.

Unlike accelerometers that use power duty cycling to achieve low power consumption, the ADXL362 does not alias input signals by undersampling; it samples the sensor’s full bandwidth at all data rates.

The ADXL362 always provides 12-bit output resolution; 8-bit formatted data is also provided for more efficient single-byte transfers when a lower resolution is sufficient. Measurement ranges of ±2 g, ±4 g, and ±8 g are available, with a resolution of 1 mg/LSB on the ±2 g range. For applications where a noise level lower than the ADXL362’s normal 550 μg/7Hz is desired, either of two lower noise modes (down to 175 μg/7Hz typ) may be selected at minimal increase in supply current.

In addition to its ultra-low power consumption, the ADXL362 has many features to enable true system-level power reduction.

It includes a deep multimode output FIFO, a built-in micropower temperature sensor, and several activity detection modes including adjustable-threshold sleep and wakeup operation that can run as low as 300 nA at a 6 Hz (approximate) measurement rate. A pin output is provided to directly control an external switch when activity is detected if desired. In addition, the ADXL362 has provisions for external control of sampling time and/or an external clock.

The ADXL362 operates on a wide 1.6 V to 3.6 V supply range, and can interface, if necessary, to a host operating on a separate, lower supply voltage. The ADXL362 is available in a 3 mm × 3.25 mm × 1.06 mm package.

ADXL362主要特性:

Ultra low power

Power can be derived from coin cell battery

1.8 μA @ 100 Hz ODR, 2.0V supply

3.0 μA @ 400 Hz ODR, 2.0V supply

300 nA motion-activated Wake-up Mode

10nA Standby Current

Built-in features for system-level power savings:

Adjustable-threshold sleep/wake modes for motion activation

Autonomous interrupt processing without need for microcontroller intervention, so the rest of the system can be turned off completely

Deep embedded FIFO minimizes host processor load

Awake state output enables implementation of standalone motion-activated switch High resolution of 1 mg/LSB

Low noise down to 175 μg/@Hz

Wide supply and I/O voltage ranges: 1.6 V to 3.6 V

Operates off 1.8V to 3.3V rails

Acceleration sample synchronization via external trigger

On-chip temperature sensor

SPI digital interface

Measurement ranges selectable via SPI command

Small and thin 3 mm × 3.25 mm × 1.06 mm package

ADXL362应用:

Hearing aids

Home healthcare devices

Motion-enabled power save switch

Wireless sensors

Motion-enabled metering devices

图1. ADXL362功能方框图

ADXL362评估板EVAL-ADXL362Z

The EVAL-ADXL362Z is a simple breakout board that enables easy connection of an ADXL362 micropower, 3-axis, digital-output MEMS accelerometer into an existing system. Due to its small size, the EVAL-ADXL362Z has minimal effect on performance of the system and of the accelerometer, and thus it is ideal for evaluation of the ADXL362 in an existing system. Note that the ADXL362 must be communicated with digitally via SPI. No processor is included with the EVAL-ADXL362Z; firmware must be supplied externally by the user. Some sample firmware is available at the link below:

The EVAL-ADXL362Z-MLP is a complete system for real-time evaluation of the ADXL362 micropower, 3-axis, digital-ouptut MEMS accelerometer. This system is accompanied by a graphical user interface (GUI) that facilitates evaluation of parameters such as power consumption, temperature coefficient, noise, and more. The system consists of a motherboard and a satellite board. The sensor is housed in a socket on the satellite board, enabling evaluation of multiple parts using one evaluation system.

To order the complete system, order the EVAL-ADXL362Z-MLP. This kit includes a motherboard, satellite board, accelerometer, and cables. Additional satellite board kits can be ordered using the part number EVAL-ADXL362Z-S. Satellite kit orders include a satellite board and an accelerometer.


图2. 评估板EVAL-ADXL362Z外形图

图3.评估板EVAL-ADXL362Z电路图

图4.评估板EVAL-ADXL362Z卫星板电路图
详情请见:
http://www.analog.com/static/imported-files/data_sheets/ADXL362.pdf
和
http://www.analog.com/static/imported-files/eval_boards/Motherboard_Schematic.pdf
以及
http://www.analog.com/static/imported-files/eval_boards/Satellite_Board_Schematic.pdf