基于LTC6994-1的FPGA在线维护看门狗屏蔽系统
电子技术应用
王鸿雪,李鹤群,单宝钰
中车大连电力牵引研发中心有限公司
摘要: 准确控制门极驱动信号引脚输出状态是多电平控制系统在线程序维护的关键技术。克服传统看门狗芯片无法监控在线程序维护过程的固有缺点,形成了窗口期覆盖1 μs至33.55 s的看门狗屏蔽电路。利用FPGA维护过程中自身引脚电平变化规律,结合LTC6994-1芯片的边沿延迟特点,对门极驱动信号进行输出使能。为验证该系统的可行性,构建了基于LTC6994-1的FPGA在线程序维护看门狗屏蔽电路硬件实物及仿真模型。测量结果显示,在线程序维护过程中,该系统既能完成对门极驱动信号输出状态的控制,又能可靠复位程序维护故障。
中图分类号:TN702 文献标志码:A DOI: 10.16157/j.issn.0258-7998.268278
中文引用格式: 王鸿雪,李鹤群,单宝钰. 基于LTC6994-1的FPGA在线维护看门狗屏蔽系统[J]. 电子技术应用,2026,52(11):8-12.
英文引用格式: Wang Hongxue,Li Hequn,Shan Baoyu. FPGA in-system programming watchdog masking system based on LTC6994-1[J]. Application of Electronic Technique,2026,52(11):8-12.
中文引用格式: 王鸿雪,李鹤群,单宝钰. 基于LTC6994-1的FPGA在线维护看门狗屏蔽系统[J]. 电子技术应用,2026,52(11):8-12.
英文引用格式: Wang Hongxue,Li Hequn,Shan Baoyu. FPGA in-system programming watchdog masking system based on LTC6994-1[J]. Application of Electronic Technique,2026,52(11):8-12.
FPGA in-system programming watchdog masking system based on LTC6994-1
Wang Hongxue,Li Hequn,Shan Baoyu
CRRC Dalian R&D Co., Ltd.
Abstract: Accurately controlling the output status of gate drive signal pins is the key technology for in-system programming in multi-level control systems. To overcome the inherent drawback of traditional watchdog chips in monitoring the in-system programming process, a watchdog masking circuit with a window period ranging from 1 µs to 33.55 s has been developed. By using the pin level variation patterns of the FPGA during the process, combined with the edge delay characteristics of the LTC6994-1 chip, the output of the gate drive signal is enabled. In order to verify the feasibility of this system, a physical hardware and a simulation model of the FPGA in-system programming watchdog masking circuit based on the LTC6994-1 are constructed. The experimental results show that during the in-system programming process, the system can not only control the output status of the gate drive signal, but also reliably reset program maintenance faults.
Key words : FPGA;in-system programming;watchdog masking;LTC6994-1;multi-level control
引言
FPGA凭借其硬件级并行架构,在多电平控制领域应用广泛,但其缺乏硬件自复位机制,需依赖外部看门狗芯片保障可靠性[1-4]。嵌入式看门狗方案主要分为三类[5-6]。第一类如文献[7]所述,采用外置复位周期可调的看门狗芯片。但复位周期设置面临两难:复位周期过短,易导致FPGA在线维护时误复位;复位周期过长,致使FPGA正常运行监控缺失,均不利于系统。第二类如文献[8-9]提出的片上程序构建看门狗,此方式仅能监控程序加载后的运行状态,无法处理加载过程中的卡滞。第三类如文献[10]利用其他的处理器监控加载过程,此方式中其他的处理器本身存在程序跑飞风险。上述方案多聚焦于系统运行阶段,对在线维护等关键场景关注不足。文献[11]虽利用JTAG的TCK信号解决MCU下载时的复位冲突,但该方法依赖专用仿真器。对于如文献[12]研究中所述无需仿真器的FPGA热启动动态加载场景,则无法使用JTAG信号对看门狗芯片进行屏蔽。在多电平控制领域,FPGA在线程序升级过程中,IGBT门极驱动脉冲信号输出的可靠性至关重要,因为任何信号异常都可能导致功率器件误导通,进而引发设备损坏。因此,亟需一种针对FPGA在线程序维护过程的看门狗屏蔽机制,以确保维护过程中IGBT门极驱动脉冲信号可靠关断,并在维护失败时,保留系统复位能力。
本文详细内容请下载:
https://www.chinaaet.com/resource/share/2000007339
作者信息:
王鸿雪,李鹤群,单宝钰
(中车大连电力牵引研发中心有限公司,辽宁 大连 116000)

此内容为AET网站原创,未经授权禁止转载。
